ADP® - Acoustic Doppler Profiler

Alicante, Spain

South of Oahu, Hawaii

Redmond, Washington

Oahu, Hawaii

Straight of Hormuz

The SonTek ADP (Acoustic Doppler Profiler) is a high-performance, 3-axis (3D) water current profiler that is accurate, reliable, and easy to use. The ADP uses state-of-the-art transducers and electronics designed to reduce side-lobe interference problems that plague other current profilers. This allows the ADP to make the very near-boundary (surface or bottom) current measurements critical to shallow water applications. The 1.5-MHz profiler is available as a Mini-ADP featuring a compact transducer head designed for applications where small size is critical.

  • Features
  • Specifications
  • Software
  • Directional Waves FAQs

With hundreds of satisfied users around the world, the ADP is proven, capable and versatile. Whether your application is hydrology, oceanography or harbor monitoring, there is an ADP configuration to suit your needs. Here is some of what sets the SonTek ADP apart.

Standard Features

  • 0.25, 0.5, 1.0, and 1.5-MHz models
  • Profiling ranges up to 180m
  • Side-looking configurations for horizontal profiling
  • Bottom Tracking & GPS input for moving boat applications
  • Compass and 2-Axis Tilt Sensor
  • All ADP software is compatible with Windows Vista/XP/2K
  • ViewADP software for post-processing
  • Low power consumption
  • Temperature sensor
  • Low price
  • Proven SonTek reliability

ADP Illustration

Optional Features

  • SeaBird MicroCat CT Sensor
  • Optical Backscatter Sensor (OBS)
  • Internal Recording
  • Pressure Sensor (Strain Gage)
  • Pressure Sensor (Frequency–RPT)
  • Directional wave measurement capabilities - SonWavePro option allows custom plots for Polar displays, Time-series displays, and Spectral displays

Over the past decade, current profilers have greatly expanded the ability to make detailed current measurements in challenging field applications. Since its introduction in 1994 as the first profiler designed specifically for shallow water environments, the ADP has revolutionized the current profiler market.

Specification
Maximum Profiling Range 1500 kHz: 15m to 25m
1000 kHz: 25m to 35m
500 kHz: 70m to 120m
250 kHz: 160m to 180m
Velocity — Range (up to 100 range cells) ±10 m/s
Velocity — Resolution 0.1 cm/s
Velocity — Accuracy ±1% of measured velocty, ±0.5 cm/s
Power Input 12-24 VDC
Typical Continuous Operating Power Consumption 2.0 to 5.0 W frequency and configuration dependent
Typical Sleep Mode Power Consumption < 1 mW
Battery capacity (alkaline, 3 packs at 5°C) 1800 W·h
Compass/Tilt Sensor — Resolution 0.1°
Compass/Tilt Sensor — Heading Accuracy ±2°
Compass/Tilt Sensor — Pitch, Roll Accuracy ±1°


CurrentMonitor Screenshot

CurrentMonitor Software — v 2.71 — 28Jan2002

CurrentMonitor is a Windows-based real-time and post-processing software program designed specifically for use in stationary/moored applications where discharge data is not required. The easy-to-use software allows you to confidently measure current profiles in less time than ever. Requirements: any up, down, or side-looking ADP (neither bottom-tracking nor GPS is needed).

CurrentSurveyor Screenshot

CurrentSurveyor Software — v 4.60 — 05Jan2007

ADP real-time and postprocessing software for open ocean applications where discharge data is not needed. Requires down looking, mobile ADP with bottom-track (with or without GPS).

*Note: A software license is required to run this program, which requires that the ADP has the bottom-track option. If your ADP has the bottom-track option installed, but you have not received a software license to run CurrentSurveyor, you can request a CurrentSurveyor software license.

Important: If you have a version of CurrentSurveyor that is earlier than v4.20, we recommend that you UNINSTALL the "old" version before installing the "new" version. This is REQUIRED for any of our beta testers.

Request a License

DeployADP Screenshot

DeployADP Software — v 1.70 — 07Dec2001

DeployADP is a Windows-based program that can be used to either plan or set up a SonTek Acoustic Doppler Profiler (ADP) for an autonomous (stand-alone) deployment. This easy to use program even has a feature that offers suggestions for what certain parameter settings should be based on just one entry -- profiling range. Based on your entries,  DeployADP lets you know if you will have enough battery power and recorder space to complete your deployment.

RiverSurveyor Screenshot

RiverSurveyor Software — v 4.60 — 05Jul2007

(NOTE: Please refer to "RiverSurveyor LIVE" software for use with RiverSurveyor S5 & M9)

ADP real-time and postprocessing software for discharge data applications - typically rivers, streams, estuaries. Requires down looking, mobile, bottom-tracking ADP (with or without GPS). Includes the RiverSurveyor System Manual.

A software license is required to run this program, which requires that the ADP has the bottom-track option. If your ADP has the bottom-track option installed, but you have not received a software license to run RiverSurveyor, you can request a RiverSurveyor software license.

Important: If you have a version of RiverSurveyor that is earlier than v4.20, we recommend that you UNINSTALL the "old" version before installing the "new" version. This is REQUIRED for any of our beta testers.

Request a License

Stationary Measurement Screenshot

Stationary Measurement — v 1.20 — 05Jul2007

The Windows-based Stationary Measurement real-time and post-processing software program was designed specifically for use in rivers. The features in this software make the ADP a more powerful tool, and allow you to reliably use our RiverSurveyor systems in more places than ever before. The RiverSurveyor system includes a built-in compass—essential when measuring discharge with a profiler from a vessel in moving-bed conditions. Combined with the Stationary Measurement software, the system can be used from a floating vessel in moving bed conditions without the need to use complicated (or undependable) DGPS systems. In northern climates, RiverSurveyor systems can even be used "year-round" with the ability to make discharge measurements under ice!

Note: This software is licensed.

New Users: Without a license, this software will not operate. You may purchase the program and accompanying license by contacting SonTek Sales.

Request a License

ViewADP Screenshot

ViewADP — v 4.03 — 12Jul2005

ViewADP is a Windows-based data display and analysis program. It is a post-processing package designed specifically for use with the data collected by any SonTek Acoustic Doppler Profiler (ADP). ViewADP allows you to quickly and easily look at and export ADP data in a variety of ways: Contour plots, time-series graphs, 2D/3D profiles, ASCII text files.

ViewADPPro Screenshot

ViewADPPro — v 4.03 — 12Jul2005

ADP/PC-ADP data display and analysis software. This "Pro" version supports directional wave measurement studies and advanced data analysis. Requires directional waves option.

*Note: A software license is required to run this program. This license requires that you purchase the directional waves option. If you have this option, but have not received the required software license, you can request a ViewADPPro software license.

Request a License

ADP Firmware — v 9.9 — 24Jan2011

SonTek has released ADP firmware version 9.9.  This firmware corrects an issue in all previous firmware versions affecting autonomous deployments in 2011 and beyond. For additional details please refer to the Release Document included in the firmware package.

PCADP Firmware — v 17.4 — 24Jan2011

SonTek has released PCADP firmware version 17.4.  This firmware corrects an issue in all previous firmware versions affecting autonomous deployments in 2011 and beyond. For additional details please refer to the Release Document included in the firmware package.

Poseidon ADP Firmware — v 8.0 — 24Jan2011

SonTek has released Poseidon ADP firmware version 8.0.  This firmware corrects an issue in all previous firmware versions affecting autonomous deployments in 2011 and beyond. For additional details please refer to the Release Document included in the firmware package.

Get Software

SonWave-Pro wave spectra software package uses the proven PUV method for directional wave measurement. This method requires accurate measurement of pressure (P) and horizontal velocities (UV) at data rates high enough to resolve wave energy (typically 2 Hz or higher).

Most of our instruments (ADP, ADV, Hydra) allow you to collect the data needed for directional wave measurements. In some cases, upgrading the capabilities of an existing system is fairly simple and does not require the return of the system to SonTek.

Directional Wave System Requirements

ADV, Hydra These instruments are already capable of the appropriate measurement rates. As long as the system has a pressure sensor, all that is needed is the PUV software package.
ADP To gather accurate velocity data at rates sufficient for directional wave analysis, the SonTek ADP uses a modified measurement strategy. Burst sampling of highly accurate short-range measurements for waves is interspersed with the standard current profiles.

The SonWave-Pro software package offers flexible processing schemes, custom plots (surface, polar, mesh), time-series displays, spectral displays, and wave statistics. The software can create publication quality graphics. Most of our instruments (ADP, ADV, Hydra) allow you to collect the data needed for directional wave measurements.

Burst StatisticsDirectional Wave Energy DistributionWave Spectral Energy

Frequently Asked Questions

Q. How do SonTek ADPs measure directional waves?

A. Our systems measure time series of pressure (P) and horizontal velocities (UV). A combination of auto and co-spectra yields the wave height, direction, and spreading.

Q. I thought that Doppler profilers could not measure velocity fast enough for wave work.

A. This is essentially true. But, we do not need to measure the full profile to get directional waves, because all we need is the velocity in the vicinity of the pressure sensor. We apply a Doppler technique known as "Pulse Coherent Processing" to measure bursts of velocity at short range. This technique is the same highly-accurate technique that we use for our ADV, and Hydra systems. Using this technique allows the ADP to periodically gather bursts of highly-accurate PUV data at rates of up to 4 Hz — which is generally the maximum rate of interest for wave work.

Q. Is this technique new?

A. Yes and no. The idea of setting a profiler to periodically measure bursts of high-resolution velocity in a single layer to combine with a pressure measurement is new, but the PUV technique for measuring directional waves has been firmly established over the past decades as a very robust measurement technique that is preferred by most researchers.

Q. I have been told that the PUV technique is unreliable because recent research indicates that the mean currents must be considered in these analyses.

A. There has indeed been recent research that indicates that mean currents above a certain size can influence wave measurements. This is not a problem, because the ADP also measures the mean current profile in addition to the PUV bursts.

Q. So how is your technique different from that used by other ADCP manufacturers?

A. The techniques are vastly different. The beam technique is a newly developed way to treat the beam velocities of a profile as a spatial array. The great advantage of PUV measurements is that they all take place in a single location: as soon as you go to an array, you must assume spatially homogenous flow over the entire array. It might be worth noting that many of the early deployments of profilers using the beam technique required the use of nearby SonTek sensors (measuring PUV) to help calibrate their results.

Q. Since the beam technique allows me to take my measurements near the surface even though my instrument is on the bottom, it seems to me that I will be able to gather wave data from significantly greater depths.

A. Not really. The Nyquist limit on wavelengths is that an array can resolve waves no shorter than twice the spacing between measurements. Most profilers have an off-vertical angle of 20-30 degrees, which means that a profiler deployed 50-m deep will create an array with measurement points a minimum of 73-115 m apart, making the minimum measurable wavelength 146-230 m. For reference, 10-second waves have wavelengths of 150 m.

Q. I understand that I do not need a pressure sensor to use the beam technique.

A. Using acoustics to measure the distance to the surface is tricky, at best. First of all, the sampling bandwidth available for surface measurement decreases with range. Second, the fact that the beams intersect the surface at an angle allows for significant contamination from leaking side-lobe energy. Last, changes in the density of the water column (e.g., a thermocline) will affect the speed of sound, and therefore the associated level measurement. In summary, while it is possible to make the measurements without using a pressure sensor, it is much less reliable to do so.

Options & Accessories

Sea Floor Mount

Sea Floor Mount

Trawl resistant design and easy underwater instrument retrieval.

Spotlight

ESRI Ocean GIS Initiative

ESRI's Ocean GIS Initiative

The Esri's Ocean GIS initiative has been motivated by the need to provide effective mapping tools and techniques to respond to recent disasters such as the Deepwater Horizon oil spill in the Gulf of Mexico and the Tohoku-Oki earthquake and tsunami in Japan. It is also motivated by assist in the implementation of the United States National Ocean Policy, particularly in the area of coastal and marine spatial planning... (link and permission courtesy Esri).